销售咨询热线
15953126901
15153196527
公司新闻 hengye
企业案例 case

联系我们

  • 联系人:济南燕翔铁艺制品有限公司
  • 手机:15953126901
  • 电话:15153196527
  • 邮箱:785385551@qq.com
  • 地址:济南市天桥区历山北路黄台不锈钢市场3区317
当前位置: 首页 > 新闻资讯>公司新闻

院门生锈,先看焊缝

来源:http://www.jnghbxg.com 日期:2026-11-18 发布人: 浏览次数:1次

院子里的铁艺大门,刚装上时线条利落、黑亮有型,两三年后却开始从某个角冒黄水、掉漆、立柱根部鼓锈。多数人以为是“漆不好”,其实锈点几乎不落在大平面上,而是集中在焊点、切口、拼缝、立柱埋地段这四处。大门耐不耐用,看的就是这几个隐蔽位置怎么处理。

The wrought iron gate in the yard, when first installed, had sharp lines and a shiny black appearance. However, two or three years later, it began to show yellow water, paint peeling, and rusting at the base of the pillars from a certain corner. Most people think it's because the paint is not good, but in fact, rust spots hardly fall on large surfaces, but are concentrated in welding points, cuts, joints, and buried sections of columns. The durability of the gate depends on how these hidden positions are handled.

14

焊点:生锈的头号起点

Solder joint: the number one starting point for rust

两块方管对接、花件与主框搭接,焊完留下焊瘤、飞溅和微小气孔。打磨不到位,底漆刷上去也盖不住针孔,水汽钻进去从里往外锈。规矩做法是焊完先敲药皮、角磨机顺纹路磨平,焊缝过渡圆滑不留凹坑,再补一道环氧富锌底漆点焊口,最后才整体刮腻子喷面漆。只喷面漆不处理焊缝,等于给锈留了后门。

Two square tubes are docked, and the decorative parts are overlapped with the main frame, leaving weld beads, splashes, and small air holes after welding. The polishing is not in place, and even when the primer is applied, it cannot cover the pinholes. Moisture seeps in and rusts from the inside out. The standard practice is to first strike the coating and use an angle grinder to smooth out the grain after welding. The transition of the weld seam should be smooth without leaving any pits. Then, a layer of epoxy zinc rich primer spot welding should be applied, and finally, putty and topcoat should be applied as a whole. Spraying only topcoat without treating the weld seam is equivalent to leaving a rear door for rust.

切口与端头:最容易漏喷

Cut and end: the most likely to leak spray

方管下料后的敞口端、装饰花的剪切面、门铰座边缘,很多作坊喷漆时朝一个方向扫,背面和端面吃漆薄。正确顺序是:切割完先倒钝去毛刺→端头封口焊或打密封胶→底漆浸泡式刷涂端面→再整体喷涂。空心管不封端,雨水从顶端灌进管腔,里面锈穿外面才看得见,那时候已经救不回来。

The open end of the square tube after cutting, the cutting surface of the decorative flower, and the edge of the door hinge seat are often swept in one direction during painting in many workshops, resulting in thin paint on the back and end faces. The correct sequence is: after cutting, blunt and deburr first → seal and weld the end or apply sealant → soak the primer and brush the end face → then spray the whole body. The hollow tube is not sealed at the end, and rainwater flows into the tube from the top. It can only be seen through rust inside and outside, and by then it cannot be saved.

拼缝与夹层:藏水不露水

Splicing and interlayer: hiding water without dew

双开门中缝、装饰圈与主管的搭接缝、铆钉周边,只要有两片金属贴在一起又没满焊,就是毛细缝。雨水靠表面张力渗进去,烘干慢、漆进不去。处理办法:能满焊的满焊,不能满焊的用中性硅酮耐候胶挤缝压实,别用普通玻璃胶(两年就粉化)。

The double door seam, the overlap seam between the decorative ring and the main pipe, and the rivet perimeter, as long as there are two pieces of metal stuck together but not fully welded, are all fine seams. Rainwater seeps in through surface tension, causing slow drying and difficulty in getting paint in. Solution: For those that can be fully welded, use neutral silicone weather resistant adhesive to squeeze and compact the seams. Do not use ordinary glass adhesive (which will powder after two years).

立柱埋地段:看不见的死穴

Column burial location: invisible dead hole

门柱如果是直接插混凝土里,水泥碱性强、透气差,管外壁半年就返锈。稳妥做法是柱底先热浸镀锌(440–470℃锌液浸镀),埋段再刷两道沥青防腐,露出地面 10–15cm 处做滴水沿或不锈钢包脚,别让积水顺着柱子倒灌进管腔。

If the door post is directly inserted into concrete, the cement has strong alkalinity and poor air permeability, and the outer wall of the pipe will rust back after six months. A safe approach is to first hot-dip galvanize the bottom of the column (440-470 ℃ zinc solution immersion), and then apply two layers of asphalt anti-corrosion coating to the buried section. A drip edge or stainless steel foot should be made at a height of 10-15 cm above the ground to prevent water from flowing back into the pipe cavity along the column.

日常养护两句话

Two sentences on daily maintenance

每半年拿软布擦一遍浮尘,别用钢丝球;发现某颗铆钉或焊点发黄,局部砂纸打掉→补富锌底漆→补同色面漆,别等连成片再整门重喷。铰链滴两滴机油,别滴到漆面上。

Wipe the floating dust with a soft cloth every six months, do not use steel wire balls; If a rivet or welding point is found to be yellowed and partially sanded off, apply zinc rich primer and topcoat of the same color. Do not wait until it is connected before re spraying the entire door. Drop two drops of engine oil on the hinge, do not drip it onto the paint surface.

铁艺门这东西,远看是造型,近看是焊口。造型抄得再像,焊点偷一步,三年就现原形;焊口和端头做扎实,普通碳钢管也能扛住济南这种夏雨冬雪的气候。

The iron gate looks like a shape from a distance, but up close it looks like a welded joint. No matter how similar the design is, if you steal one step from the solder joints, the original shape will appear in three years; The welded joints and ends are made solid, and ordinary carbon steel pipes can withstand the climate of summer rain and winter snow in Jinan.

本文由济南铁艺大门友情奉献.更多有关的知识请点击:http://www.jnghbxg.com我们将会对你提出的疑问进行详细的解答,欢迎你登录网站留言.

This article is a friendly contribution from Jinan Iron Art Gate For more information, please click: http://www.jnghbxg.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message